Why Screws Shake Loose on Competition Robots (and Why Threadlocker Cracks Plastic)

Screws back out because match vibration breaks static thread friction, while liquid threadlocker shatters polycarbonate and 3D prints by triggering environmental stress cracking.
Screws back out of competition robots because dynamic transverse vibration—the side-to-side rattling caused by drivetrains, planetary gearboxes, and robot collisions—repeatedly relieves the clamping force holding the fastener stretched, allowing the thread pitch to act as an inclined plane down which the screw freely spins. Threadlocker cracked your plastic parts because standard anaerobic threadlockers (such as blue Loctite 242) contain methacrylate esters that rapidly attack amorphous thermoplastics like polycarbonate and 3D-printed filaments under mechanical tension, inducing catastrophic Environmental Stress Cracking (ESC).
The Physics of Backout: Why Standard Fasteners Fail in Matches
A tightened bolt is not a rigid peg; it is a very stiff spring. When you tighten a machine screw into a tapped hole or standard hex nut, you stretch the bolt shank axially. That elastic stretch creates preload—the clamping force that squeezes your chassis channels or motor mounts together. In a stationary robot, static friction between the male and female thread flanks prevents the screw from unwinding.
During a competition match, that static friction disappears thousands of times per minute. While axial shock loads (pulling straight along the screw) rarely loosen a properly torqued bolt, transverse vibration (shear movement perpendicular to the screw axis) is fatal to standard hardware:
- Microscopic slip: Impact shocks from crossing field obstacles or running mecanum wheels on perimeter field tiles cause joined metal plates to slide sideways by mere micrometres.
- Frictional zeroing: When two surfaces slide sideways against each other, the effective friction resisting rotational unwinding momentarily drops to zero.
- The inclined plane effect: The helix angle of the thread provides a permanent directional bias. Each time the friction drops to zero under a sideways jolt, the elastic tension in the bolt uncoils a fraction of a degree down the ramp of the thread.
Within thirty seconds of intense defence or high-speed intake cycling, a completely tight standard M3 or M4 screw can run completely free of tension. Once preload drops to zero, the screw backs out entirely and falls onto the arena floor.
The Chemistry Disaster: Why Liquid Threadlocker Destroys Plastics
The standard workshop reflex to loose bolts is reaching for a bottle of medium-strength anaerobic threadlocker. On an all-metal assembly—such as steel motor pinions or aluminium channel junctions—anaerobic threadlocker works exceptionally well. When applied to 3D-printed parts, acrylic panels, or clear polycarbonate (Lexan) shields, it is destructive.
Standard threadlockers are anaerobic dimethacrylate esters. They are engineered to do two things: remain liquid in the presence of atmospheric oxygen, and polymerise into a hard cross-linked thermoset plastic when isolated from air in the presence of active metal ions (such as iron or copper). When you use them on or near plastics, two separate failures occur:
- It fails to cure: Thermoplastics and 3D-printed resins contain no active metal ions. Without metal catalysts to drive the reaction, the liquid anaerobic monomer remains uncured for days or weeks.
- It induces Environmental Stress Cracking (ESC): Polycarbonate and common 3D-printing materials like PLA, PETG, and ABS are amorphous or semi-crystalline polymers held together by long, entangled polymer chains. When you tighten a screw through a plastic bracket, those chains are placed under sustained tensile stress. The uncured methacrylate monomers are small, chemically aggressive molecules that diffuse directly into the strained intermolecular spaces between polymer chains. They act as rapid plasticisers, lubricating the chains and allowing them to untangle and slip apart under the existing mechanical tension.
The result is not melting or chemical burning; it is instantaneous, brittle shattering. A polycarbonate bracket exposed to anaerobic threadlocker will develop a web of milky, microscopic fissures (crazing) around the bolt hole and fracture straight through the joint under hand pressure.
Cyanoacrylate adhesives (superglue) cause identical failures. Cyanoacrylates outgas acidic fumes as they polymerise, which redeposit on adjacent plastics, aggressively crazing polycarbonate windows and making PLA prints so brittle that screw heads pull clean through their countersinks on first impact.
The Fastener Hierarchy: What Actually Works on Robots
To survive competition vibrations without chemically dissolving your intake arms and chassis brackets, replace liquid chemical reliance with mechanical retention:
| Fastener / Method | Vibration Resistance | Safe with Plastics? | Best Used For |
|---|---|---|---|
| Standard Nut + Spring Washer | Extremely Poor | Yes | Bench prototypes only; ban from competition robots. |
| Nylon-Insert Lock Nut (Nyloc) | Excellent | Yes | Structural metal chassis, polycarbonate panels, pivot shafts. |
| Serrated Flange Screw / Nut | Very Good | No (Gouges plastic) | Heavy structural aluminium-to-aluminium joints. |
| Brass Heat-Set Threaded Inserts | Moderate (needs Nyloc/compound) | Yes | Custom 3D-printed motor mounts and structural housings. |
| Anaerobic Threadlocker (Blue) | Excellent | No (Severe ESC) | Blind holes in aluminium/steel where a nut cannot fit. |
| Pre-applied Polyamide / Vibra-Tite | Good to Excellent | Yes | Screws going directly into plastic or metal tapped holes. |
1. Standardise on Nylon-Insert Lock Nuts (Nylocs)
For pass-through holes, nylon-insert lock nuts are the gold standard. The undersized polymer collar inside the collar of the nut deforms elastically around the male threads of the screw. This exerts constant radial prevailing torque that does not depend on fastener tension or bolt stretch. Even if your joint takes a structural hit that slightly bends an aluminium plate and eliminates axial preload, a Nyloc will not shake off the end of the screw.
2. Stop Split-Ring Lock Washers from Entering the Workshop
Helical spring (split) washers are largely useless on high-vibration competition robots. Once a split washer is compressed flat, it behaves almost entirely like a standard flat washer. When dynamic transverse loads slide the joint, the hardened split edges gouge into the softer aluminium or plastic, accelerate surface wear, reduce clamp preload, and actually hasten joint loosening.
3. Handle 3D-Printed Parts Mechanically
Never thread metal machine screws directly into printed plastic threads for structural applications. Plastic creeps (deforms permanently under sustained stress) over 48 hours, which drops bolt preload to zero without the screw ever rotating. Use brass heat-set inserts pressed in with a soldering iron tip, or design captive hexagonal pockets in your CAD model to hold standard steel Nyloc nuts behind the plastic wall.
4. Use Non-Anaerobic Compounds When Blind Tappings Are Unavoidable
If you must secure a screw into a blind tapped hole on a planetary gearbox face or custom plate where a Nyloc nut cannot fit, use a solvent-evaporating acrylic compound (such as Vibra-Tite VC-3) instead of an anaerobic liquid. These compounds are applied to the screw threads, allowed to air-dry completely for ten minutes before installation, and function purely as a viscous, friction-adding mechanical cushion. Because they contain no active liquid monomers when driven into the hole, they will not attack surrounding plastics or printed mounts.
If you are rebuilding a drivetrain or preparing a competition chassis, standardising your pit hardware around high-tensile steel button heads and matching Nyloc nuts (available individually through our store or integrated into modular drive packs at Sheen Robotics FTC resources) will eliminate the bulk of match-stopping mechanical failures before robot inspection opens.
The Pre-Match Fastener Inspection Routine
Never test bolt tightness with high-torque electric drivers in the pit five minutes before a queue call. High-torque drivers strip aluminium threads, crush 3D-printed perimeters, and strip hex sockets. Instead, establish a methodical pit protocol:
- The Paint-Pen Witness Mark: Once a critical joint is correctly torqued, draw a fine line with a white paint marker across the screw head and onto the adjacent plate. During queueing, pit crews can visually confirm every structural screw is locked in place without touching a single hex key. If the line is cracked or misaligned, the fastener has rotated.
- Check Cold Flow: Bolts clamped through polycarbonate panels or 3D prints will lose preload naturally as the plastic slowly yields under the washer face. Tighten plastic-clamped joints by hand with a manual Allen key, using broad flat washers to spread the clamping area and prevent the head from sinking into the material.



